Touch Screen Display
You can buy just the display to use with an existing digital load cell solution or buy a complete kit with Load Cells and USB interface device and a display. The DS-3000 display is meant to replace common LCD/LED displays that typically are available for use with scales and load cells.
Please note that the DS-3000 display MUST be used with a digital load cell or a resistive load cell mated and calibrated with a USB interface.
All Displays and Controllers shipped in 2026, come with a basic 2 point calibration utility as well as the ability to enter a mV/V calibration value. But if you want to display, log the data and plot data, do a detailed 9 point recalibration of your digital load cells, get remote support, easy access to utilities and customize your display then you should purchase LoadVUE Pro, SensorVUE or ControlVUE software that run on a Windows 11 PC/Tablet.
DS-3000-Pro Touch Screen Display Quick Links
Highlights
The DS-3000-Pro display can be used with any of our USB load cell solutions. When powered up, it launches straight into an application that shows available connected USB load cell(s). Connect the sensor+interface devices into the USB port and then turn on DS-3000-Pro to activate the display. The DS-3000-Pro is powered by a 5V switchable power adapter that is provided as part of the purchase.
Initialize Sensors
Tare or zero-out initial values and then start viewing the sensor data
Customize Settings
Set number of points to average to reduce noise, select measurement units, and adjust resolution (x, x.x, x.xx, x.xxx) as needed
Enable Alerts
Set limits to trigger audio and/or visual alerts. Automatic overload protection alerts are enabled to alert you and prevent sensor damage
Calibration
Perform simple 2-point calibration directly from the display. Or simply enter the mV/V value provided by your manufacturer for a quick and dirty working calibration
Single and Four-Channel
DS-3000-Pro-1 can connect to a single load cell+interface pair. Connect upto four load cell + digital interface pairs to the DS-3000-Pro-4 . The four channel version displays the individual as well as the total of up to four connected digital USB load cells.
Connect our Capacitive or Resistive Sensors
iLoad, iLoad Pro, iLoad TR USB Capacitive load cells; iLoad Mini Capacitive load cells with DQ-1000U or DQ-1000UHS interface; any of our Resistive load cells paired with our Digital Interfaces (DI-1000U/DI-1000UHS or DI-100U/DI-100UHS or DI-400U/DI-400UHS)
View Sensor Data
View force and weight data on a responsive touchscreen display. The Peak and Low values are also displayed
If you want to control external devices using USB Relays to build simple automation, use our digital controllers DC-100 (for single channel) or DC-400 (for four channel).
Button Load Cell with USB Interface and Display
If you need to display force values on a simple LCD display, simply connect the load cell to the DI-1000U Digital Load Cell Interface & use the USB connector on the DI-1000 to connect to the USB port of the DS-3000-Pro. If you need to log or plot data then you can connect the DI-1000U output to a PC and use LoadVUE Pro software to display, log and plot data.
Suggested Kit:
RSB2 Button Load Cell
DI-1000U Load Cell Interface
DS-3000-Pro
Add Compression Calibration
Four USB Load Cell Kit with Four Channel Display
Suggested Kit:
Four REB5 Button Load Cells
DI-400U 4 Channel USB Interface
DS-3000-Pro-4 Four Channel Display
SensorVUE Software
Add Calibration
Displays for Capacitive USB Load Cells
The DS-3000-Pro displays work with capacitive as well as resistive load cells. They are compatible with the iLoad Series load cells including the iLoad, iLoad TR and iLoad Pro USB load cells. They are also compatible with the iLoad Mini and iLoad Mini Pro load cells when connected with the DQ-1000U USB Load Cell interfaces and calibrated together as show below.
Suggested Kit:
iLoad Mini Load Cell
DQ-1000U USB Interface
Calibration in Tension
DS-3000-Pro-1 Display
Add Accessories
Capacitive Load Cell with DS-3000-Pro LCD Display
The DS-3000-Pro displays work with capacitive as well as resistive load cells. They are compatible with the iLoad Series load cells including the iLoad, iLoad TR and iLoad Pro USB load cells. If you don't want to use a PC or PLC and just want a simple LCD display, you can use our DS-3000-Pro Touch Screen LCD Display as shown below with an iLoad Pro USB load cell.
Suggested Kit:
iLoad Pro USB Load Cell
DS-3000-Pro-1 Touch Screen Display
Compression Calibration
Cable & USB Dongle
Simple 2-Point Calibration
Using the Calibration Utility, you can perform a simple 2-point Calibration on the connected sensor. You will need standard dead-weights to perform this calibration.
Set and Trigger Alerts
You can define the high and low thresholds to trigger audio and visual alerts. Just enter the desired values and select the type of alert (audio or visual aert or both).
Alternatives
If you are looking to control external devices using the sensor data, you can use DC-100 or DC-400 touchscreen display and controller.
DC-100
Single-channel touchscreen display and controller
Connect to a USB Relay to control external devices
Define high and low values and set alerts
Connect with our capacitive and resistive load cells
DC-400
Four-channel touchscreen display and controller
Connect to a USB Relay to control external devices
Define high and low values and set alerts
Connect with our capacitive and resistive load cells
Watch and Learn
Using DS-3000-Pro
Display Calibration
Setup DS-3000-Pro
FAQ
This display was developed precisely to allow a user to display forces without using a PC or Tablet for various reasons
The display can accept either capacitive USB load cells or resistive load cells connected to a DI-100U, DI-1000U or DI-400U USB Load Cell Interface.
We offer two versions. A single channel version - the DS-3000-Pro-1 and the four channel version - the DS-3000-Pro-4. The four channel version can accept and display from up to four connected USB or BLE load cells or load cell+ interface pairs.
The DI-1000BLE has a built in rechargeable battery that can work cordlessly for 1-2 hours on a full eight hour recharge. The DS-3000-Pro display requires a 5V power supply through a micro USB connector. If you have a back battery pack with a micro USB output then you can operate the display on a battery.
NTEP is standard set by the US Dept. of Commerce for weighing systems used for trade to sell products by weight. If you sell say coffee beans by the lb then you are supposed to use an NTEP rated scale (and hence an NTEP rated load cell). The Display is NOT NTEP Rated. But if you use an NTEP rated load cell with the DI-1000U USB or DI-1000BLE that can handle better than +/- 0.02% accuracy needs, then you should be able to get it certified yourself if needed.
Any resisitve load cell that is mated with a DI-100U or DI-1000U or DI-400U or wirelessly via BLE protocol (DI-1000BLE) is compatible with the DS-3000-Pro display. Any Capacitive load cell with USB output directly or via a DQ-1000U or DQ-4000U is compatible with the display.
No. Currently you can go from the usb interface to a PC directly. Or you can go to the display. You cannot go from the display to the PC yet.
Yes. We offer calibration service on new sensor purchases as well as recalibration service for previously purchased sensors. We use NIST traceable reference standards to perform and validate the calibration and provide a free calibration certificate as part of the service. We are NOT ISO certified.
You can register on our website, login and see all prices, download spec sheets and solid models. You can also send us an email with your contact information and shipping address and we will be happy to send you a formal quote.
We give you a 30 day guiarantee for you purchase. You can exchange or return your purchased products for a refund of the purchase price of the product. Any calibration service fees, shipping and payment fees cannot be refunded. Feel free to try out our products risk free and see for yourself how easy we make it for you!
We need between one and two weeks usually to ship your order for items in stock. This is because we have to make your sensor, interface and calibrate them together, make sure the quality meets all specs and then pack and ship it to you. We offer expedited processing options if you are in a rush and need to get sensors sooner. If out of stock or if sensors are needed in volume, we could take 4-6 weeks or longer. Please contact us to get an estimate of price and lead time for your particular needs.
We believe teaching young kids and encouraging R&D is crucial to make this world a better place. We support teaching and research activities in educational institutions with a 10% education discount on purchased products in exchange for sharing write ups, pictures, video clips and other material we can use in our marketing materials on and off line.
